FAQs

Why Is My Skateboard So Loud?

There may be a number of causes if you’re wondering why your skateboard is making so much noise. Firstly, a grinding sound when riding may be the result of old or unclean bearings. Second, rattling and noise might be produced by loose trucks or wheels. Thirdly, cycling on unlevel ground might increase noise levels. 

Furthermore, harder wheels may be noisier than softer ones, and bad riding technique may also contribute to noise. Consider lubricating and cleaning your bearings, tightening loose parts, choosing softer wheels, and modifying your riding approach to lessen noise. These actions will help you ride your skateboard more quietly.

Vibrating decks, loud trucks, and jingling wheels. It’s a common occurrence, and it may be really annoying. There are a few causes for the sound made by your skateboard or longboard.

  • Loose base plate screws.
  • Badly worn bushings.
  • Broken pivot cup.
  • Dried-up bearings.
  • washers with wheels.
  • Badly secured or missing lift pads.
  • Tire problems, such as flat patches or wheel hardness.

Why Is My Skateboard So Loud?

There are several reasons why your skateboard may be making a lot of noise. One of the major causes of noisy skateboards are as follows.

  • Worn Bushings.
  • Loose Bearings.
  • Loose Bolts or Nuts.
  • Old Grip Tape.
  • Wheel Alignment Issues.

Worn Bushings:

Usually trucks have two bushings to aid in turning and absorb stress from road or trick hits. When traveling over shocks or rough surfaces, you may hear creaking sounds if these have worn out and become loose. Changing these bushings is a simple task if you have the necessary equipment, so give that a try first if you think that’s what’s causing the noise.

Loose Bearings:

Your wheels’ loose bearings are another prevalent source of the noise. Skating’s friction can wear these down over time, making them vibrate and make a buzzing noise as you ride. To correct this, loosen the axle nut and make sure there is no dirt or debris between the wheel’s bearings and the nut.

Read more: New Skateboard Bearings Are Slow

Loose Bolts or Nuts:

Loose nuts and bolts are the most prevalent reason for noise on a skateboard. If you look closely at the baseplate of your truck, you will notice that it is held together by a number of screws. Make careful to examine each one to determine whether or not it is properly fastened. You don’t want them to be excessively loose, but you also don’t want it to be too tight, because that might cause long-term damage to the metal threads.

Old Grip Tape:

Grip tape is important for keeping your feet securely placed on top of the board when riding, but it can wear out with time, causing a squeaky sound when either foot presses down with pressure (this frequently occurs when pushing off). Changing out the grip tape with new, high-quality tape should solve the problem. You’ll be glad you did it eventually.

Wheel Alignment Issues:

If the weight isn’t evenly distributed over all four wheels due to poor wheel alignment, strange noises can result from the tires rubbing against the pavement. Just before taking off again, ensure that each of the wheels are correctly aligned by shifting them about a bit until they are.

How can I make my skateboard quite? (Guide to fix)

Skaters know how frustrating it is to be in a middle of a session when their board begins making an unpleasant rattling noise. It’s not just uncomfortable, but it may also be embarrassing when out on the road. Thankfully, there are a few options for making your skateboard less noisy. Let’s examine five examples of this. 

Tighten All Bolts:

The first thing you need to do is check the tightness of every single bolt on your board. A wheel that has even one loose bolt can make a lot of sound as it rotates. You don’t want to overtighten them; you simply want them to stay in place while you ride and shake the board. 

Change Bearings:

If you haven’t done so in a while, you should probably do so because worn-out bearings can be very noisy. Investing in new bearings would not only improve performance but also reduce noise. 

Put On Some Risers:

Risers are tiny bits of wood or plastic that fit within the baseplate and board of your board to give it a slight lift (about 1/8 to 1/4 inch). This prevents the wheels from creating annoying noise as they rub against the deck, and it also extends the life of both the deck and the wheels. 

Add Spacers:

You can purchase spacers for the tires to prevent them from moving around and making noise when you travel over bumps and gaps in the road. Make sure you acquire the right size and thickness for your board prior to installing them, as the amount of space needed between the tire and deck varies from configuration to setup. 

Lubricate Axles And Bearings:

If everything else fails, lubing your shafts and bearings might help lessen some of the clanking noises that come from riding a skateboard too quickly or on rough surfaces like asphalt or dirt roads. Silicone-based lubricants are safe for your board’s rubber parts, but they wear off fast owing to the heat produced by friction during rides and must be reapplied frequently.

Conclusion: 

Skateboard trucks and the skateboard deck are two places to check if you hear squeaking. You may require new bushings, trucks, or even a brand new skateboard.

Use some soapy water to lubricate the important sections of your skateboard if the trucks squeak or if the board itself makes squeaking noises. You can find numerous skate tools on Amazon to fix things like squeaky bushings and skateboard trucks.

I believe this FAQ was helpful, and if your board is making any strange noises, you can try cleaning it with liquid soap. I at Stoked are familiar with the common issues you may encounter because we have repaired numerous noisy boards. Your skateboard’s loud noise could be the result of a few different factors. There is no one problem that will always be present, such as a faulty bearing or bushing.

If you follow our easy instructions, you should be able to diagnose the issue and resolve it. Our full skateboard is cheap, durable, and surprisingly silent, so it’s worth picking up if you’re in need of a new board.

Read more: